Controle-Sans-Fil-Blogspot: Oktober 2015

2015/10/28

How to Achieve Remote Dimmer

Remote dimmer means more convenient. I use rf wireless receiver http://www.ourautomation.com/2-way-wireless-telephone-remote-control-module-with-password-6-ringing-p-161.html and a mobilephone for remote dimmer. Besides for remote dimmer, it can Control variety of home appliances and electronic products in any place worldwide by fixed telephone or mobile phone.

How To hoist heavy stuff with winch controlled by remote controller easily

My parents are farmers who always store the grain in the warehouse in every harvest season. But the warehouse sometimes is an attic. They usually have to hoist grain bag to the attic by themselves in the past. Actually, that is energy-consuming working. It is too difficult for aged parents to hoist those heavy bags of grains now. So they want to know if there is an easier way to hoist grain.

So I choose this set of controller, Model 0020337（S1FM-DC12&CV-2）which is strongly recommended by the supplier. They said the major characteristic of this receiver is to make the motor in the winch rotate in positive and reversal direction. That is to say, the rope of winch will be stretched out and drawn back by wireless remote controller. The transmitter is also easy to use for my parent.

Here are transmitter and receiver.

We install immediately. The wires from the winch are connected to the receiver. Then we just try to hoist heavy stuff. We hook up the bag, pressing and holding button ▲ on transmitter. With the motor of winch working continuously in the “UP” direction, the rope is drawn back and the bag is hoisted; When the bag is hoisted to the attic, release button ▲, the motor of winch stops working. After putting away the grains bag, we press and hold button ▼ on transmitter, the motor works continuously in the “DOWN” direction , the rope is stretched out and then it reaches the ground.

Online shop: www.ourautomation.com

2015/10/27

How to Remote Control Water Engine

How to Remote Control Water Engine

One of our customers needs to control the engine of my garden pump to water easily. The actual range is 100 meters. The pump engine requires 220 volt, 1000 watt power. He thinks that an external antenna is necessary for the receiver.

We would like to recommend the remote control model with 3 modes 0020489 S1PUA-AC220-ANT2&CB-2. With normally open terminals, working voltage range of relay can be AC110~240V or DC0~28V. The maximum working current is 30amp. So it can activate a 220V, 1000W motor. In addition, the working distance of transmitter and receiver with external extend antenna is 2000m (6000ft) theoretically without barriers. Its working distance is farther than your actual range.

Wiring is also fairly simple.

Just follow the wiring diagram. The pump engine is connected to normally open terminals A&B on the receiver and supplied 220V power supply. Then we can connect receiver to power supply too.

Operation:

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Press big button, turn on the pump engine.

Press small button, turn off the pump engine.

Online shop: www.ourautomation.com

Movement Detector And Time Delay Receiver For Water Feature Pump Motor

Question from customer:

“I have a waterfall water feature that currently has an 110v 250W pump that run from 7AM until 10PM. I would like to save more energy by having these pumps turn on by detecting motion near the water feature. 110 degree detection, within 30 feet would be sufficient. The more intelligent, the better (i.e. body/heat/motion/mass detection). There is no need to run a waterfall water feature when no one is there to enjoy it. What do you recommend?”

Fallsview water feature and front entrance

Answer:

We recommend wireless infrared movement detector and receiver with time delay function (S1DA-AC220-ANT2&W-01) to you. This kit is 220V actuated. With external extended antenna, it can work within 6000ft in the open field. With adjustable time delay function, you can adjust delay time from 0 second to 99 hours. The motion detector can detect any movement within 10m. Detection range is fan-shaped angle 110°.

We’d like show you how to use this kit.

Steps:

1 Using screws to fix the bracket on the wall to favorable locations according to your need (i.e. the corridor towards waterfall water feature) and put the detector on the bracket, then adjust the detector to the suitable angle of 10~14° and turn on it.

2 Wire pump motor to B terminals of receiver (A, B = Normally Closed; B, C = Normally Open). Press buttons of “＋” and “－” on the timer of receiver, “H” is Hour, “M” is Minute, and “S” is Second. We suggest you that you can set your pump work every 30 minutes from 7AM to 10PM. Once people pass corridor towards waterfall water feature, the motion detector is triggered. You can set “M30”. And supply power to receiver and pump motor.

3 When the movement detector is triggered: Turn on relay (connect B and C, disconnect A and B).

The pump motor begins to work. It will last 30 minutes if you set “M30”. After delay time, there is no motions any more, it will turn off by itself.

How to Achieve Remote Control Christmas Tree

Remote control christmas tree can be easily done with rf wireless products. In this video, I want to remote control Christmas tree by the products in online shop http://www.ourautomation.com I use DC Power Output Single Channel RF Remote Receiver Circuit - 3 Control Modes http://www.ourautomation.com/dc-power-output-single-channel-rf-remote-receiver-circuit-3-control-modes-p-1414.html.
So it seems remote control Christmas tree is quiet interesting and I want to share with you.

How to Remote Control 6 Water Motorcycles

Water motorcycle is a recreational vessel that the rider sits or stands on, rather than inside of, as in a boat. Most are designed for two or three people. Water motorcycles are small, fast and fairly easy to handle and use. Besides recreational function, they are preferred for non-recreational function in accidents to pick up flood survivors. Also, there are obvious hazards of collisions and mechanical breakdowns of water motorcycles. How to prevent from accidents in time?

Someone wants to remote control 6 water motorcycles from long distance. That is a idea that from the beach, he is able to control the switch of a user that is getting wild or getting to close to danger. If we discover danger in advance, we can stop the water motorcycle.

He uses six 12VDC direct power output receivers with the long distance remote to control his water motorcycles.

Wire 6 water motorcycles to 6 receivers respectively and press button on and off to turn on or shut down water motocycles.

When any of water motorcycles is getting wild or getting to close to danger, he can press any button to stop any of them to prevent from accidents. What’s more, it is the long range remote control which can help him control water motorcycles from long distance.

2015/10/26

How to Achieve Hot Water Circulator Remote Controlling

A man wants to use one device to turn on a hot-water circulator in his home for 15 minutes&then has it automatically turn off. He lives in a 2 story wood home&the hot-water circulator is in the basement-maybe a distance of about 30 ft away through drywall&wood flooring.

Wiring program is as follow:

He can connect delayed remote unit to circulator pump. The receiver is relay output (normally open and normally closed). Power supply for the receiver and the water pump are different. That means it will not cause electromagnetic interference during water pump operation.

Operation:

Press big button: Turn on relay (connect B and C, disconnect A and B). After delay time: Turn off relay by itself (disconnect B and C, connect A and B). Press small button: Turn off relay immediately, no need to wait for delay time.

Press buttons of “＋” and “－” on the timer, adjust delay time from 0 second to 99 hours. “H” is Hour, “M” is Minute, and “S” is Second. As his requirement, he can set “M 1 5”, it means the delay time is 15 minutes. After working for 15 minutes, it will be off automatically. Then the circulator pump stops pumping.

view details: http://www.ourautomation.com/-p-739.html

Online shop: http://www.ourautomation.com

Christmas Firework Remote Control

Christmas firework can be controlled by rf wireless remote control kit. It can ignite Christmas firework through fireworks electric igniter, which reduces accidents like skin burn and accidental explosions. One ignitor can light several fireworks at the same time.One transmitter can control many Christmas firework ignitors simultaneously. The ignitor can be remotely controlled from any place within a reliable distance; wireless signal pass through walls, floors and doors. Working distance of the Chritmas firework remote controller with external extend antenna: 100M / 300ft (theoretically)
View details: http://www.ourautomation.com/2-ch-100m-rf-wireless-remote-control-firework-ignitor-system-p-1564.html
Online shop: http://www.ourautomation.com
Email: dolores_rf@yahoo.com
Skype: ourautomation

How to Achieve Christmas Light Remote Controller

Christmas light remote controller means that turning on/off the Christmas is more convenient and the Christmas day will be more funny. With a wireless RF remote control kit, we can easily control the Christmas light or other equipments in a long distance. The long range of it can reach 1 miles, 2 miles or 3miles in different. And there is no worry about if the Christmas light remote controller has turned on/off the light successfuly in a long distance, with the two-way feedback function, when the receiver gets the signal of transmitter, it will immediately send a return signal to the transmitter. The feedback function of Christmas can let the user know whether he/she had already connect the transmitter and receiver successfully in such a long distance.
View details of this Christmas light remote controller:
http://www.ourautomation.com/-p-1745.html
Online shop: http://www.ourautomation.com
Email: dolores_rf@yahoo.com
Skype: ourautomation

2015/10/24

6V Remote Controller for Doorbell

A man wants to install a single channel remote to control his doorbell within the range of 150m. The old 6V doorbell was broken and he doesn’t want to repair the wires of doorbell. Ordinary wireless doorbell cannot be used because it doesn’t reach the distance he really wants. He has an idea that a transmitter is connected to the doorbell button and relay in receiver is connected to doorbell. The only problem is the control range of remote need to reach about 150m.

Answer:

We recommend the 6V one channel 2000m receiver(S1U-DC06-ANT2) and long range transmitter (CB-1). Working voltage range of receiver is 6V. With normally open and close terminal, the voltage of the device being controlled is AC110~240V or DC0~28V. So it can be applied in 6V doorbell. Usually, you don’t have to supply additional power to doorbell because it can get 6V power from powered receiver when you connect them to the 6V power supply together. And the most significant is that it has extended external antenna which makes its control range up to 2000m (6000ft).

According to his requirement, he can connect the button of the bell to the transmitter by two wires. Then connect the bell to the relay in the receiver.

Setting control mode Momentary: Connect Jumper-1.

When he presses the button of the bell, RF signal will be sent out from transmitter to receiver. The receiver receives to turn on the relay, then the doorbell rings. Release the button, the doorbell stops ringing.

View details: www.ourautomation.com/-p-582.html

Online shop: www.ourautomation.com

Intellegence Garbage Bin——By RF Vibration Detector

I just want to use wireless remote controller to attach his garbage bin outside. When the truck picks up the bin and tips garbage, the controller will detects and turns up a light in the house. So I can know that the garbage is taken away and I can fetch the inner garbage can back. It sounds a very innovative idea. I have no idea to realize it?So I searched on the internet and asked a remote control supplier, they select a remote control kit for me. That is model 0020259 & model 0010032 (S1DA-AC220 & W-12). They are the remote control kit with functions of vibration reminder and time delay.

They told me that W-12 is an RF vibration detector. When the item is vibrated, the vibration detector will be triggered and will send signal to the receiver toinstruct the device to work. S1DA-AC220 is a receiver with a timer.

It looks like great.

With the procedure they shown, I stick the detector to the garbage bin and pull out the antenna. (To see the following picture)

Then I begin to wire. The power supply should be connected to the N&L terminal of the receiver. Wires from the light should be connected to B&N terminal of the receiver. Then I use another wire connect to C&L terminal of the receiver. (Wire as the wiring picture they show me)

The operation time came, I press buttons of “＋” and “－” on the timer to adjust delay time. I set 5 minutes for this timer.

When the truck comes and picks up the garbage bin, the garbage bin is vibrated so that the vibration detector is triggered and the light will shine and last for 5 minutes. Then the light will turn off automatically after 5 minutes. With shining of light, I know that the garbage truck tips garbage into truck and takes away, so I can fetch my inner garbage can back. I like this little , useful, handy gadget.

Online shop: www.ourautomation.com

2015/10/23

RF Reminder for Deaf Dog

A man would like to know which kind of vibrators will be strong enough to alert a deaf dog. He’d like to hook it to a collar and use it to train the dog and to also alert him.

Golden Retriever on beach with stick Original Filename: 86485865.jpg

50M RF remote control reminder with 4 Vibration Modes (Z-02&CS-4) is suitable for him. This remote vibrator has two parts: vibration receiver and transmitter. It is small enough for you to carry in the pocket. Press the button on transmitter and the receiver will vibrate to alert. The receiver can be controlled by transmitter from any place within a reliable distance; wireless signal pass through walls, floors and doors. It is suitable for person or animal with hearing impairment.

With antenna, its transmitting distance is about 50M. There are vibrator, LED indicator, battery, and learning button in the receiver.

The first step is deleting and learning codes:

1 Delete all stored codes:

Press and hold the button of the receiver for about 2 seconds until LED light is off, then release the button, all stored codes have been deleted successfully. At this time, the transmitter cannot control the receiver.

2 Learning remote controls:

Press the learning button of the receiver, LED light is on, the receiver is in the status of LEARNING.

Press any button of remote control within 7 seconds, if LED light flashes twice slowly then off, it means LEARNING is successful. If LED light is off after 7 seconds, it means LEARNING is failed and the receiver quits the status of LEARNING.

The second step is operation:

The receiver can learn several remote controls of different codes.

Press button A: The receiver vibrates once.

Press button B: The receiver vibrates twice. Press button C: The receiver vibrates three times. Press button D: The receiver vibrates four times.

When you press the button on transmitter, the receiver will receive the wireless signal and vibrate. Then the dog can feel the vibration.

View details: http://www.ourautomation.com/alerting-vibrator-reminder-c-455.html

Online shop: http://www.ourautomation.com

2015/10/22

1000M 315Mhz / 433Mhz Wireless RF Signal Repeater [0010001 (R-01)] - US $43.65 : Our Automation, Our Automation, Remote Light Switch Online Shop

2 Big Button Industrial Remote Control 1000m Industrial Light Switch/Industrial Door Switch/Industrial Motor Switch [0021068 (CBW-2)] - US $47.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2 Big Button Industrial Remote Control 1000m Industrial Light Switch/Industrial Door Switch/Industrial Motor Switch [0021068 (CBW-2)] - US $47.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

1 CH AC Long Range Wireless Remote Control Kit Relay Output 30A High Power 5000M Waterproof with Feedback Function [0020106] - US $144.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

1 CH AC Long Range Wireless Remote Control Kit Relay Output 30A High Power 5000M Waterproof with Feedback Function [0020106] - US $144.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2015/10/20

RF Motor Control with Time Delay Funtion and Positive or Reversal Direction

RF Motor Control can be used for DC equipments. It has time delay function, the delay time of this RF motor control is customized according to actual requirements. View details of this RF motor control: http://www.ourautomation.com/-p-1474.html Online shop: http://www.ourautomation.com Email: dolores_rf@yahoo.com Skype: ourautomation

RF Motor Control Direct Current 12V or 24V 2000M Motion Telescopic Aerial [0020608 (S1PF3-ANT3)] - US $58.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2015/10/17

12CH 10A 2000M Long Range Radio Frequency Remote Control - 3 Receiver & 1 Transmitter 110V 220V [0020408 (3S4UB-AC220-ANT2 & CB-12)] - US $125.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

12CH 10A 2000M Long Range Radio Frequency Remote Control - 3 Receiver & 1 Transmitter 110V 220V [0020408 (3S4UB-AC220-ANT2 & CB-12)] - US $125.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2000M 12 Channel 10A DC 6V/9V/12V/24V Power Output RF Remote Control Kit 1 Transmitter & 12 Receiver [0020345 (12S1XB-DC06/09/12/24-ANT2 & CB-12)] - US $305.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2000M 12 Channel 10A DC 6V/9V/12V/24V Power Output RF Remote Control Kit 1 Transmitter & 12 Receiver [0020345 (12S1XB-DC06/09/12/24-ANT2 & CB-12)] - US $305.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2000M 12 Channel 10A DC 6V/9V/12V/24V Power Output RF Remote Control Kit 1 Transmitter & 12 Receiver [0020345 (12S1XB-DC06/09/12/24-ANT2 & CB-12)] - US $305.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2000M 12 Channel 2000W 110V/220V Power Input & Output RF Remote Control [0020343 (12S1XB-AC220-ANT2 & CB-12)] - US $325.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

12 Channel DC Power 2000M Long Range Wireless Remote Control System - 12 Control Modes [0020274 (S12CA-DC09/12/24-ANT2 & CB-12)] - US $66.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

12 Channel DC Power 2000M Long Range Wireless Remote Control System - 12 Control Modes [0020274 (S12CA-DC09/12/24-ANT2 & CB-12)] - US $66.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

12 Channel DC Power 2000M Long Range Wireless Remote Control System - 12 Control Modes [0020274 (S12CA-DC09/12/24-ANT2 & CB-12)] - US $66.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

8CH 2000M 10A Wireless Remote Control Switch - 2 Receiver & 1 Transmitter 110V 220V [0020407 (2S4UB-AC220-ANT2 & CB-8)] - US $90.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

10A DC 8 Channel RF Wireless Remote Control System for Home Appliances 2000M [0020389 (2S4UB-DC09/12/24-ANT2 & CB-8)] - US $85.00 : Our Automation, Our Automation, Remote Light Switch Online Shop

2015/10/15

How to Control Winch Motor by Time Delay Controller with Limit Switch

Someone is looking for a 120vac powered remote control for winch. He needs 1 motor control 120vac with ability to stop when limit switch reached. Also like delay for start direction of ac motor.

Forward &Reverse Motor controller is 110V~220V power actuated, which also enjoys time delay function and limit switch. It focuses on capability of motor forward-reverse-stop. Wireless signal pass through walls, floors, doors and other obstacles if he remote controls he winch motor within a reliable distance from any places. With time delay function, the working time can be adjusted from 10 to 60 seconds. What’s more, the limit switch can prolong or shorten delay time through its clockwise or anti-clockwise rotation. It really meets his need.

Wiring and operation will be explained in more detail from following procedure and picture.

Wiring procedure:

Connect the live wire to the “L”, and the zero wire to the “N”. Connect AC motor to the “OUT” and the zero wire. You can exchange output wires of motor to change the rotating direction of motor.

Operation:

Press button ▲: Light 1 shines, motor rotates in the positive direction, and it will stop after a certain delay time.

Press button ▼: Light 2 shines, motor rotates in the reversal direction, and it will stop after a certain delay time.

The delay time of positive / reverse rotation can be adjusted from 10 to 60 seconds. Turn R1/R2 clockwise, prolong the delay time. Turn R1/R2 anti-clockwise, shorten the delay time. When you press button ▲ or button ▼, the motor starts to rotate; It will stop after the delay time is expired.

When the rotation is overdone, if switch S1 or S2 is activated, the motor will stop automatically.

After press button ▲, you must press button ■ to stop the motor firstly, and then press button ▼.

If he pulls out the Jumper of the receiver, you can press directly button ▼ after press button ▲.

Online shop: http://www.ourautomation.com

One controller controls many video cameras—How to realize?

You decided to install a security system with video camera in somewhere in you new house, the door gate, garage, porch, living room, bedrooms. Maybe you wonder whether it is possible to wire some video cameras to be controlled by one remote controller or not. We have many kinds of remote transmitters and we consider a set handy electronic gadget can help you. CB series transmitter,(www.ourautomation.com) Model 0021027(CB-6) is one of those transmitters, which can connect with 6 receivers. It pairs with the receiver, Model 0020360(S1UB-DC12). You can control video cameras with just one remote controller easily.

It is so easy to install. Look at the wiring picture.

Wires on the video camera should be connected to the receiver and power supply. From the picture, the red wire from the video camera is connected to B terminal of the receiver and the black wire is connected to negative electrode of the power supply. The positive wire of the power supply is connected to C terminal of the receiver.
The transmitter and receivers should come to the “Toggle Mode”. This means pressing each button controls each video camera on or off separately.
When press button 1, the transmitter is triggered and sends out an RF signal “ON” to the receiver. After the receiver receives the signal, the corresponding video camera is on. When press button 1 again, the transmitter is triggered and sends out an RF signal “OFF” to the receiver. After the receiver receives the signal, the corresponding video camera is off…
It is really a simple and convenient way to control all video cameras from one remote controller.
Online shop: http://www.ourautomation.com

2015/10/14

Mini Remote Control for Lights / Doors /Motors

Mini remote cotnrol is portable and light. The receiver PCB Size of this mini remote cotnrol is 22mm x 11mm x 5mm. The transmiiter Unit size of this mini remote control is 58mm x 39mm x 16mm. The wireless RF signal can pass through walls, doors, floors and so on.

View details: http://www.ourautomation.com/-p-1808.html

Online shop: http://www.ourautomation.com

Email: dolores_rf2yahoo.com

Skype: ourautomation

2015/10/09

Momentary Firework Ignition with New Firework Ignition System

Momentary firework ignition system has been promoted recently. It can ignite various kinds of electric fireworks directly, just like momentary fireworks which go off in a second. Remote control firework ignition reduces accidents like skin burn and accidental explosions.

It contains 12-button remote transmitter and 12-channel ignitor. Each channel can ignite about 25 fireworks simultaneously. It also has many features including test function, voltage indicator, waterproof case and manual operation mode. Wireless signal pass through walls, floors and doors. The remote control distance is 500m/1500ft (theoretically).

First of all, we should prepare materials. We have firework ignitor, remote transmitter and momentary firework.

This is the wiring. Wire momentary fireworks to the ignitor, the fireworks can be remotely controlled by remote transmitter from any place within a reliable distance.

Press button 1, ignite firework 1.

Press button 2, ignite firework 2.

Press button 3, ignite firework 3.

Momentary firework ignition system:

http://www.ourautomation.com/-p-1615.html

Online shop:

http://www.ourautomation.com

How to Remote Control Concrete Pump

Someone needs a one channel, 12 volt, one button toggle on off switch, heavy duty for outdoor wet, dusty rough vibrating conditions. This devise will be mounted on a concrete pump and will need to operate from a distance of 200m with obstructions.

Answer:

We thought that you should have high power and long distance remote controller. We recommend this 30 ampere multi-mode long range remote control (S1PU-DC12/24-ANT2 & CB-2). This 1 channel 30A long range remote control operates in toggle, momentary and latched mode (set the mode as you like freely). It can be used to control lights, motors, electrically operated doors / locks / windows / blinds / cars or other appliances with AC110~240V or DC0~28V. With external extend antenna, the transmitter and receiver have longer working range, up to 2000M.

Now we’d like to show you how to remote control 12V concrete motor. See the wiring diagram below, B is normally open terminal; C normally closed terminal and A common terminal. Connect motor to Terminal A&B. And motor and receiver will share the same power supply as the following diagram.

Online shop:

http://www.ourautomation.com

The kit:

http://www.ourautomation.com/-p-1095.html

6 Amplifiers’ Remote Controlling

David has a big square bunch of trees. He wants to buy 6 12VDC receivers and place 1 receiver connected to 1 amplifier in every corner of the trees. Then he will stay in the dark place and operate them with the remote control. Remote distance should be 100m.

So we recommend 6-channel receiver and 6-button transmitter (S6C-DC12-ANT2+CB-6) to David. This gadget will be more convenient for him. He can wire 6 amplifiers on one receiver. But he needs long wires to connect amplifiers and receiver because he need place in every corner of the trees. It can control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with AC110~240V or DC0~28V besides amplifiers. He can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. With adding external extended magnetic antenna, its working distance is up to 2000m (6000ft) in the open filed. Five choices for working mode: Toggle, Momentary or Latched, Momentary + Toggle, Momentary + Latched. But we suggest that you may use Toggle mode which features in “Press→On, Press again →Off”.

This is the wiring diagram. A&B terminals is normally open, B&C terminals is normally closed. We usually connect lamps to normally open terminals. So amplifiers are connected to B&C terminals from relay 1 to relay 6 one by one. And supply power to the receiver. Owing to no current output for lamps from receiver, so 6 amplifiers must be supplied other power together. (See the following picture)

He can choose toggle mode, he can do like this:

Press button 1 on remote, switch on channel 1 of receiver to turn on amplifier 1

Press button 1 again, switch off channel 1 of receiver to turn off amplifier 1

Press button 2 on remote, switch on channel 2 of receiver to turn on amplifier 2

Press button 2 again, switch off channel 2 of receiver to turn off amplifier 2

Press button 3 on remote, switch on channel 3 of receiver to turn on amplifier 3

Press button 3 again, switch off channel 3 of receiver turn off amplifier 3

Press button 4 on remote, switch on channel 4 of receiver to turn on amplifier 4

Press button 4 again, switch off channel 4of receiver turn off amplifier 3

The kit:

http://www.ourautomation.com/-p-1446.html

The 6 channel receiver:

http://www.ourautomation.com/-p-205.html

The 6 button transmitter:

http://www.ourautomation.com/-p-251.html

Manual Switch to Realise Remote Controlling LED Lamp

Someone said he wanted a remote controlling unit that the transmitter was to function as a switch to the receiver activated by supplying a 12V DC current to the transmitter (switch it on). The receiver then permited a 12V DC current to be supplied to a designated appliance. When the transmitter was shut off the receiver would shut down.

According to the picture above, he wants the transmitter can be activated by manual switch and turn receiver on/off when the current in that circuit is on/off. First, the transmitter is supposed to be connected to power supply and that manual switch. Second, designated appliance should be connected to receiver.

We prepare a demonstration for this practical use.

We switch on the manual switch and the transmitter will send an “ON” signal to the receiver. The receiver receives the signal to instruct the light to turn on. We switch off the manual switch and the transmitter will send an “OFF” signal to the receiver. The receiver receives the signal to instruct the light to turn off.

Online shop:

http://www.ourautomation.com